收藏本站
MCP73853/55
5.0
5.1
5.1.1
DETAILED DESCRIPTION
Analog Circuitry
BATTERY MANAGEMENT INPUT
Figure 6-1 depicts a typical application circuit with
connection of the THERM input. The resistor values of
R T1 and R T2 are calculated with the following
equations:
For NTC thermistors:
R COLD – R HOT
R COLD – 3 × R HOT
R HOT – R COLD
R HOT – 3 × R COLD
SUPPLY (V DD1 , V DD2 )
The V DD input is the input supply to the MCP7385X
devices. The MCP7385X devices automatically enter a
power-down mode if the voltage on the V DD input falls
below the UVLO voltage (V STOP ). This feature prevents
draining the battery pack when the V DD supply is not
present.
5.1.2 PROG INPUT
Fast charge current regulation can be scaled by placing
a programming resistor (R PROG ) from the PROG input
to V SS . Connecting the PROG input to V SS allows for a
maximum fast charge current of 400 mA, typically. The
minimum fast charge current is 85 mA (Typ) and is set
by letting the PROG input float. Equation 5-1 calculates
2 × R COLD × R HOT
R T 1 = ----------------------------------------------
2 × R COLD × R HOT
R T 2 = ----------------------------------------------
For PTC thermistors:
2 × R COLD × R HOT
R T 1 = ----------------------------------------------
2 × R COLD × R HOT
R T 2 = ----------------------------------------------
Where:
the value for R PROG .
R COLD
and R HOT
are the thermistor
14.1 × I REG – 1.2
EQUATION 5-1:
13.32 – 33.3 × I REG
R PROG = ------------------------------------------------
resistance values at the temperature window
of interest.
Applying a voltage equal to V THREF /3 to the THERM
input disables temperature monitoring.
Where:
5.1.5
TIMER SET INPUT (TIMER)
t PRECON = ------------------- × 1.0 Hour s
I REG is the desired fast charge current in
amps
R PROG is in kilohms.
The preconditioning trickle charge current and the
charge termination current are scaled to approximately
10% and 7% of I REG , respectively.
The TIMER input programs the period of the safety tim-
ers by placing a timing capacitor (C TIMER ) between the
TIMER input pin and V SS . Three safety timers are
programmed via the timing capacitor.
The preconditioning safety timer period:
C TIMER
0.1 μ F
5.1.3
CELL TEMPERATURE SENSOR
t FAST = ------------------- × 1.5 Hours
BIAS (THREF)
A 2.55V voltage reference is provided to bias an
external thermistor for continuous cell temperature
monitoring and prequalification. A ratiometric window
comparison is performed at threshold levels of
V THREF /2 and V THREF /4.
The fast charge safety timer period:
C TIMER
0.1 μ F
And, the elapsed time termination period:
t TERM = ------------------- × 3.0 Hours
5.1.4
CELL TEMPERATURE SENSOR
INPUT (THERM)
C TIMER
0.1 μ F
The MCP73853 continuously monitors temperature by
comparing the voltage between the THERM input and
V SS with the upper and lower temperature thresholds.
A negative or positive temperature coefficient, NTC or
PTC thermistor, and an external voltage divider
typically develop this voltage. The temperature-
sensing circuit has its own reference, to which it
performs a ratiometric comparison. Therefore, it is
immune to fluctuations in the supply input (V DD ). The
temperature-sensing circuit is removed from the
system when V DD is not applied, eliminating additional
discharge of the battery pack.
? 2004-2012 Microchip Technology Inc.
The preconditioning timer starts after qualification and
resets when the charge cycle transitions to the
constant-current, fast charge phase. The fast charge
timer and the elapsed timer start after the MCP7385X
devices transition from preconditioning. The fast
charge timer resets when the charge cycle transitions
to the Constant-voltage mode. The elapsed timer will
expire and terminate the charge if the sensed current
does not diminish below the termination threshold.
During thermal regulation, the timer is slowed down
proportional to the charge current.
DS21915B-page 13
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MCT5201SR2M OPTOCOUPLER PHOTO TRANS 6SMD
MCT62W OPTOCOUPLER TRANS-OUT 2CH 8-DIP
MCT9001S OPTOCOUPLER TRANS-OUT 2CH 8-SMD
MCZ33099EGR2 IC VREG ALTERNATOR ADAPT 16-SOIC
MCZ33291LEGR2 IC SWITCH 8X LOSIDE W/SPI 24SOIC
MCZ33789AE IC SBC W/PWR SUPPLY 64LQFP
MCZ33800EKR2 IC ENGINE CTRL SW/DVR 54-SOIC
MCZ33810EK IC IGNITION INJECTOR 32-SOIC
相关代理商/技术参数
MCP73855-I/MFG 功能描述:电池管理 2 CELL LI ION/POLY Lead Free Package RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MCP73855-I/ML 制造商:Microchip Technology Inc 功能描述:
MCP73855IMF 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:USB Compatible Li-Ion/Li-Polymer Charge Management Controllers
MCP73855IML 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:USB Compatible Li-Ion/Li-Polymer Charge Management Controllers
MCP73855T 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:USB Compatible Li-Ion/Li-Polymer Charge Management Controllers
MCP73855T-I/MF 功能描述:电池管理 Sgl C Lthm-Ion/Plymr RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MCP73855T-I/MFG 功能描述:电池管理 LINEAR CHG MGMT CONT Lead Free Package RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
MCP73855TIMF 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:USB Compatible Li-Ion/Li-Polymer Charge Management Controllers